Among the various factors affecting the magnetic separation process, the magnetic field strength, the rotational speed of the drum, the size of the flushing water, and the magnetic declination all directly affect the sorting index. However, as the laboratory equipment, the flushing water and the magnetic declination are fixed. Therefore, we only tested the magnetic field strength and the rotational speed of the drum. The magnetic separation test process is shown in Figure 1. Figure 1 Magnetic separation process flow chart First, the determination of the magnetic field strength of a section The pyrite cinder (dry ore) is first sieved through a 100 mesh sieve, and the sieved product is ground for 5 minutes on a rod mill. The grinding concentration is C=70%, stirred for 5-8 minutes, and the rotation frequency of the drum is 16 rpm. Under the condition of min, the magnetic field strength of one magnetic separation is 1500 oersted respectively, the current intensity of two-stage magnetic separation is 2500 Oersted, and the current intensity of three-section magnetic separation is 3000 Oersted. The test results are shown in Table 1 below. Show. Table 1 Magnetic field strength test of a magnetic separation Magnetic field strength (Oe) product name Yield(%) grade(%) Recovery rate(%) Fe S Fe S 1500 Concentrate I 29.82 59.49 0.274 34.91 4.70 Concentrate II 10.78 61.75 0.259 13.10 1.60 Concentrate III 5.83 59.98 0.321 6.88 1.08 Tailings 53.57 42.79 3.07 45.11 92.62 total 100 50.82 1.74 100 100 2000 Concentrate I 32.78 61.02 0.252 39.36 4.75 Concentrate II 6.95 61.41 0.203 8.39 0.81 Concentrate III 5.82 60.50 0.294 6.92 0.98 Tailings 54.45 42.31 2.80 45.33 93.46 total 100 50.82 1.74 100 100 2500 Concentrate I 33.68 60.11 0.223 39.83 4.32 Concentrate II 5.41 61.72 0.254 6.58 0.78 Concentrate III 5.69 59.67 0.263 6.68 0.86 Tailings 55.22 43.17 2.960 46.91 94.04 total 100 50.82 1.74 100 100 The results in Table 1 show that under the same conditions, the magnetic separation of a magnetic field with a magnetic separation of 2000 Oersted is better, and the Fe grade can reach 61.64%. If the three concentrates I, II and III are mixed, The cumulative yield is 45.55%, and the cumulative recovery rate is 54.67%. The content of S can be reduced to about 0.3%. Since the yield of the three-stage magnetic separation is low, three-stage magnetic separation will not be performed in the following flow. Determination of the magnetic field strength of the second and second sections Sulfur iron ore slag (dry ore) first sieved through a 100 mesh sieve, the sieve product in a rod mill grinding ore 5min, grinding concentration C = 70%, was stirred for 5 ~ 8min, the drum rotation frequency of 16 rpm / Under the condition of min, the magnetic field strength of one magnetic separation is 2000 Oersted, and the magnetic field strength of the second magnetic separation is 2500 ohms and 3000 ohms respectively. The test results are shown in Table 2. Table 2 Two-stage magnetic separation magnetic field strength test Two-stage magnetic field strength (Oe) product name Yield(%) grade(%) Recovery rate(%) Fe S Fe S 2500 Concentrate I 35.40 62.70 0.257 43.68 5.23 Concentrate II 12.76 61.26 0.211 15.38 1.55 Tailings 51.84 40.13 3.13 40.94 93.22 total 100 50.82 1.74 100 100 3000 Concentrate I 36.21 60.83 0.272 43.34 5.66 Concentrate II 8.07 60.47 0.280 9.60 1.30 Tailings 55.72 42.92 2.91 47.06 93.04 total 100 50.82 1.74 100 100 The results in Table 2 show that under the same conditions, the magnetic field strength of the two-stage magnetic separation is 2500 Oersted, and the magnetic grade is better. The Fe grade can reach 62.70%. If I and II concentrates are mixed, The cumulative yield was 48.16%, and the cumulative recovery was 59.06%. The content of S can be reduced to about 0.3%. Third, the determination of the rotational speed of the drum The pyrite cinder (dry mine) is sieved through a 100 mesh sieve, and the sieved product is ground on a rod mill for 5 min. The grinding concentration is C=70%, stirred for 5-8 minutes, and the magnetic field strength of a magnetic separation is 2000 Å. The magnetic field strength of the two-stage magnetic separation is 2500 Oersted, and the rotational speed of the drum is 16 rev/min, 18 rev/min, 20 rev/min, and 24, respectively. The test results are shown in Table 3. Table 3 Magnetic separator drum rotation speed test Speed ​​(rev / min) product name Yield(%) grade(%) Recovery rate(%) Fe S Fe S 16 Concentrate I 33.70 62.44 0.253 41.41 4.90 Concentrate II 15.36 60.33 0.218 18.22 1.92 Tailings 50.94 40.27 3.18 40.37 93.18 total 100 50.82 1.74 100 100 18 Concentrate I 34.15 63.46 0.247 42.64 4.85 Concentrate II 17.33 59.85 0.223 20.68 2.22 Tailings 48.52 38.42 3.33 36.68 92.93 total 100 50.82 1.74 100 100 20 Concentrate I 29.33 62.83 0.314 36.26 5.29 Concentrate II 15.43 60.13 0.236 18.28 2.09 Tailings 55.24 41.82 2.92 45.46 92.62 total 100 50.82 1.74 100 100 twenty four Concentrate I 32.29 60.37 0.283 38.36 5.25 Concentrate II 11.64 61.45 0.221 13.95 1.48 Tailings 56.06 43.23 2.89 47.69 93.27 total 100 50.82 1.74 100 100 The results in Table 3 show that under the same conditions, the magnetic separation effect is better when the rotation frequency f of the drum is 18 rev/min, and the grade of Fe can reach 63.46%. If the concentrates I and II are mixed, The cumulative yield was 51.84%, and the cumulative recovery was 63.22%. The content of S can be reduced to about 0.3%. From the results of the above tests, it can be concluded that the magnetic separation process can obtain a higher grade, but the recovery rate and the yield are not ideal. The test has made a corresponding discussion on various factors affecting the magnetic field strength of the magnetic separation process and the rotational speed of the drum. The results show that the optimal magnetic separation process conditions are: when the grinding time is 5 min, the grinding concentration is C=70%, the stirring is 5-8 min, the magnetic field strength of a magnetic separation magnetic field is 2000 Oersted, and the magnetic field strength of the second magnetic separation 2500 Oersted, adjust the magnetic separator drum rotation frequency f to 18 rev / min. Under this condition, 63.46% of Fe grade was obtained, the cumulative yield was 51.84%, and the recovery was 63.32%. The content of S is about 0.3%.
Classification of tablet press: Models can be divided into single punch tablet press, rotary tablet press, sub-high speed rotary tablet press, automatic high speed tablet press and rotary core tablet press.
The sheet shape pressed by the tablet press is initially flat circular, and later developed into shallow circular arc and deep circular arc on both sides, which is for the need of coating. With the development of special-shaped tablet press, oval, triangle, oblong, square, diamond, circular ring tablets followed. In addition, with the continuous development of preparations, due to the requirements of compound preparations and timed release preparations, special tablets such as double layer, triple layer and core coating are made, which need to be completed on special tablet press.
Rotary tablet press is a machine which is made of several pairs of die distributed on the turntable to make a circular lifting movement according to a certain track and press the granular material into tablet through the press wheel. And the stamping rod with the rotary table rotating speed ≥60m/min line press is called high-speed rotary tablet press, this high-speed rotary tablet press has a forced feeding mechanism, the machine is controlled by PLC, has the automatic adjustment of pressure, control the weight of the piece, eliminate the waste piece, print data, display fault shutdown and other functions, in addition to the control of the weight difference within a certain range, Quality problems such as missing Angle and loose lobe can be automatically identified and eliminated.
With the development of market demand, the scope of application of tablet press is more and more wide, no longer simply limited to the suppression of Chinese and Western medicine tablets, more widely suppressed health food, veterinary medicine tablets, chemical tablets: such as mothballs, washing blocks, smurf blocks, art powder, pesticide tablets, food tablets: chicken essence block, isatis root block, divine Qu tea block, compressed biscuits.
Rotary Tablet Press,Tablet Press,Tablet Machine,Tablet Maker,Pill Machine JIANGYIN CITY XUAN TENG MACHINERY EQUIPMENT CO.,LTD , https://www.machineryxuanteng.com