Red Rock Muck
Light Pole Shut & Welding Machine is mainly for making light pole.street pole.traffic pole.Flagpoles etc. The cross section of the street light pole has various shapes such as:round, octagon, dodecagon(twelve sides) and so on.Viewed from the length of the rod, it is generally tapered. We often named these poles: tapered light pole,tapered street pole .. etc. The conical traffic post is widely used in the road, the taper flagpoles are widely used in the square, citizen garden... etc.
The production of street light poles includes many processes: the cutting of trapezoidal plates, the bending of street light poles, the stitching of bending openings, the welding of bending openings, the deformation correction of street lighting poles, surface grinding, welding of ribs, surface galvanizing.
Similar Names: Light Pole welding,Taper Pole welding,Conical Pole welding ,Street Pole welding,Traffic Pole Welding ,Light pole shut and welding,Octagon Pole Shut and Welding,Flagpoles welding,Street pole sewing,Tapered pole welding, Conical pole shut and welding machine.
Production process of street lamp poles
3. Welding:Straight seam welding is performed on the bent pipe seam during welding. Since the welding is automatic submerged arc/CO2 gas shielded welding, attention should be paid to adjusting the welding position during welding to ensure the straightness of the welding seam.
4. Repair and polish:Repair and grinding is to repair the defective pipe after automatic welding. The repairers should check one by one, and repair the defective places. After the repair welding is completed, they will be repaired. The repaired joints are basically the same as the automatic welding seam.
9.Painting and installing
Light Pole welding,Taper Pole welding,Conical Pole welding ,Street Pole welding,Traffic Pole Welding ,Light pole shut and welding,Octagon Pole Shut and Welding,Flagpoles welding,Street pole sewing Wuxi Zhouxiang Complete Set of Welding Equipment Co., Ltd. , https://www.beamweldingmachine.com
With the increasing efforts to control haze across the country, measures such as the elimination of yellow-standard vehicles, the increase of vehicle emission standards, and the regulation of the qualification of waste transportation vehicles have been frequently introduced, and a new round of environmental protection actions are in full swing. In response to the green slag transportation and construction of the blue sky, SAIC Iveco Hongyan Commercial Vehicle Co., Ltd. combined the standards of slag transport vehicles in different regions and launched a series of intelligent slag transport vehicles that meet the policies and regulations with practical actions.
In view of the dumping and drip phenomenon of the slag trucks, some of the red slag slag car compartments are equipped with an electrically-operated hardtop or soft-top environmental protection cover with reliable sealing performance; for low-emission pollution with “black tail†dragging, Hongyan The slag trucks are specially matched with the green and environmentally friendly four-engine or LNG natural gas engine to reduce tail gas emissions, improve air quality, and develop green cyclists. There are many accidents such as side-dumping of dump trucks and serious overloading. Hongyan slag truck adopts 865mm. The wide frame has effectively improved the stability of the vehicle. For individual drivers' driving habits, Hongyan's muck trucks are monitored and tracked in real time through car networking, GPS, and other methods to strictly monitor and regulate the driving behavior of truck drivers. Improving the “bad impression†of the slag muck from a bit of a drop.
Throughout the industry, many red mud muck enterprises have already taken the lead in the industry. Its esteem for the concept of smart and environmental protection, from the design of body hardware to the application of intelligent driving systems, makes the operation of slag trucks more scientific, and the slogan of environmental protection is effectively supported by actual actions.
1. Cutting and cutting (rolling shearing machine)
1. Before cutting, firstly adjust the inclination of the cutting machine to match the required longitudinal scissors.
2. Determine the position of the steel plate to ensure the maximum size of the remaining material, so that the remaining material can be used.
2. Bending
Bending is the most critical process in the production of light poles. The quality of the bending directly affects the quality of the light pole and cannot be repaired after bending. The specific attention is as follows:
1. First remove the slag of the sheet, check the length, width and straightness of the sheet, the non-straightness is less than or equal to 1/1000, if the non-straightness meets the requirements, make corrections, especially the polygonal rod must ensure the non-straightness.
2.Increase the bending depth of the bending machine and determine the position of the sheet.
3.Correctly draw the line on the sheet material section, the error is ≤ soil 1mm. Correct alignment, correct bending, so that the pipe seam is minimized, and the height of the two sides is not more than 5mm.
5. Plastic surgery:The shaping process includes the straightening of the light pole and the full circle and polygonal diagonal dimensions of the two ends of the pole. The general tolerance is 1t; ± 2mm. The straightness error of the return rod does not exceed: ≤1.5/1000.
6, Milling bottom face:The flushing process is to flatten both ends of the bent tube blank to ensure that the nozzle is perpendicular to the center line, and there is no angle and height unevenness.
7. Install the bottom plate:The key to spot welding the bottom flange and the rib plate is to ensure that the bottom flange is perpendicular to the straight center line of the lamp, the rib plate is perpendicular to the bottom flange, and is parallel to the straight bus bar of the lamp.
8. Weld bottom flange:Welding requirements refer to the national standard welding process to ensure the welding quality. The welding seam should be neat and beautiful.