Chamber Shrink Packager Machine is one of the smallest among SBWPACK packaging machines. It's available in the desktop version or equipped with trolley, design with casters for easy mobility. These Manual Sealing And Shrinking Series models are suitable for companies requiring medium to small productions.
Operation of the Manual L Bar Sealer is simple. The product to be wrapped is placed in the fold film and then set into the chamber. The lid is closed which activates the L-bar sealer and circulates hot air around the package within the chamber, shrinking the film. When the package is tight enough simply lift the lid and remove the wrapped package. The simplicity, reduced overall size and the extreme versatility of the Chamber Shrink Packager without Conveyor are its best features, as well as high reliability, great performance and low power consumption, which make the Chamber Shrink Packager without Conveyor a smart alternative to basic bar seal and heat gun systems.
Chamber Shrink Packager without Conveyor System modes of packaging, shrink or seal: Transparent hood ,visible sealing and shrinking; PTFE coated sealing blade; Up to 12 pcs per minute; Center fold film applicable; Adjustable chamber height; Mobile and robust in metal frame.
Chamber Shrink Packager,Chamber Shrink Wrapper,Chamber Shrink Wrapping Machine,Chamber Shrink Wrappers SUZHOU SHENGBAIWEI PACKAGING EQUIPMENT CO.,LTD , https://www.sbwpack.com
2. Before the work, the oil should be strictly in accordance with the lubrication regulations, and the oil volume should be maintained properly, the oil path should be open, the oil mark (window) should be visible, and the oil cup, oil line, linoleum, etc. should be clean.
3. Check whether each department is in good condition, and then run it again for about 1 Omin. After confirming that each department is working properly, it will start work. If abnormal operation or abnormal temperature rise is found during work, it should be stopped.
4. The clamping of the tool must be properly tightened, the amount of extension should not be too long, the gasket should be straight and the size is the same, generally no more than two. It is forbidden to cut with a pure tool.
5. The top and hole should be wiped before loading the card, and the tools and methods should be properly selected. Attention should be paid to the smoothness and safety. To avoid touching or stinging the lathe, it is not allowed to strike straightening workpieces and tools on the lathe.
6. When installing the card wheel pair, make the centerline of the two silver degree holes lower than the top center line of the lathe 2-3mm, then slowly start the top ends of the lathe, align the top hole tightly, and check whether the tightening device is tight. Reliable, firm and tight, with Karen's fittings or levers as close as possible to the edges of the spokes, making them fast and strong.
7. Always check the status of the oil pump, oil circuit, oil level indicator, and the joysticks in various places during operation. Check whether the automatic feed mechanism and positioning pin's limit devices work well and reliably; if the safety device is firm, handle any abnormalities in time. .
8. It is forbidden for one person to operate two tool holders at the same time. When two persons are operating at the same time, they should make a call response, and iron chips should not be removed during cutting.
9. The cutting tool must not be stopped without leaving the workpiece.
10. The operator of the lathe shall not leave during operation. If it is necessary to leave, it must stop and pull open the power switch. When restarting, it is necessary to carefully check the positions of the handles of the various parts and then drive the parts without loosening.
11. No lathes and miscellaneous items shall be placed on the lathe, and the fixture shall be placed on the tool box and tool tray.
12. After the work, you must check the cleaning equipment, remove the turning tool to do the daily maintenance work, and put each operation handle (switch) in the neutral position (home position), pull the power switch to achieve neat, clean, lubricated, and safe.
1. Operators are required to obtain an operation certificate after passing the examination, and they must be familiar with the performance, structure, etc. of the machine, and must abide by the safety and shift system.